![]() ![]() Software Control via Ethernet Industry Compatible Tally System. Luminance Waveform, Vectorscope, RGB Parade, YUV Parade, Histogram, Audio phase and level.Ĭonfiguration utility for MAC and Windows. Blackmagic SmartScope Duo 4K 2 BMD-HDL-SMTWSCOPEDUO4K2 - Blackmagic SmartScope Duo 4K. The included SmartView Utility software for Mac and Windows lets you daisy chain your SmartView Duo monitors together on an Ethernet network and control them. USB 2.0 for software updates and Ethernet for configuration SmartScope Duo 4K to monitor images with extreme precision thanks to built-in waveform graphs. SMPTE 259M, SMPTE 292M, SMPTE 296M, SMPTE 372M and SMPTE 425M. ![]() The inputs are auto-sensing/switching to match the supported input video. Same with the HDMI out, when connected to a crappy little. ![]() However, if I connect the output to my 5' SmallHD SDI monitor, the signal works fine. Each monitor is independent so can display any combination of scope or picture view!Īutomatically switches between SD, HD and 6G-SDI. The SmartScope Duo 4K allows you to monitor SD, HD, 2K, and UHD 4K (3840 x 2160) video. I'm sending a signal from two devices to my MultiView 4 HD (2018 release) but cannot get a signal going from the SDI output to either of my Panasonic BT-LH1700WP HD monitors. The cameras and the Decimators both output Level A, I am not sure if the cameras will output Level B but I can convert it in the Decimator to Level B. Luminance Waveform, Vectorscope, RGB Parade, YUV Parade, Histogram, Audio phase and level.Ĭonfiguration utility for MAC and Windows.ġ2V universal power supply included with international socket adapters for all countries.ġ2 Months Limited Manufacturer’s Warranty.Blackmagic Design SmartScope Duo 4K 2 SMTWSCOPEDUO4K2 looks like a SmartView Duo but adds independent waveform monitoring so you can select between waveform, vectorscope, RGB parade, YUV parade, histogram and audio phase level displays. The Smartscope Duo 4k accepts SDI Level B and will not accept SDI Level A single. USB 2.0 for software updates and Ethernet for configuration : Plugging In Your Computer Blackmagic SmartView setup can be installed on multiple networked computers if desired. When no video is received by the unit, the backlight turns off, saving power until the next valid signal is received. But then when I connect it via USB, it tells me its running 4.0, and never offers to update anything. I checked all possible software: Blackmagic Device Video Setup. SMPTE 259M, SMPTE 292M, SMPTE 296M, SMPTE 372M, SMPTE 424M Level B and SMPTE 425M. SmartView 4K and SmartScope Duo 4K also detects Ultra HD 4K. When I connect it via Ethernet, the SmartView software tells me 'Software Version: Earlier than 4.0, Version 4.0 available for update', and to connect via USB to update the software. Each monitor is independent so can display any combination of scope or picture view!Īutomatically switches between SD, HD and 6G-SDI. The SmartScope Duo 4K features waveform waveform monitoring, RGB parallax vectorscope, YUV parade, histogram and audio phase with audio level display. SmartScope Duo 4K looks like a SmartView Duo but adds independent waveform monitoring so you can select between waveform, vectorscope, RGB parade, YUV parade, histogram and audio phase level displays. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |